View MC74HC4066-D_2952218.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

this document, mc74hc4066/d has been canceled and replaced by mc74hc4066a/d lan was sent 9/28/01 http://onsemi.com
mc54/74hc4066 quad analog switch/ multiplexer/demultiplexer highperformance silicongate cmos the mc54/74hc4066 utilizes silicongate cmos technology to achieve fast propagation delays, low on resistances, and low offchannel leakage current. this bilateral switch/multiplexer/demultiplexer controls analog and digital voltages that may vary across the full powersupply range (from v cc to gnd). the hc4066 is identical in pinout to the metalgate cmos mc14016 and mc14066. each device has four independent switches. the device has been designed so that the on resistances (r on ) are much more linear over input voltage than r on of metalgate cmos analog switches. this device is identical in both function and pinout to the hc4016. the on/off control inputs are compatible with standard cmos outputs; with pullup resistors, they are compatible with lsttl outputs. for analog switches with voltagelevel translators, see the hc4316. ? fast switching and propagation speeds ? high on/off output voltage ratio ? low crosstalk between switches ? diode protection on all inputs/outputs ? wide powersupply voltage range (v cc gnd) = 2.0 to 12.0 volts ? analog input voltage range (v cc gnd) = 2.0 to 12.0 volts ? improved linearity and lower on resistance over input voltage than the mc14016 or mc14066 or hc4016 ? low noise ? chip complexity: 44 fets or 11 equivalent gates logic diagram x a y a 12 a on/off control 13 x b y b 43 b on/off control 5 x c y c 89 c on/off control 6 x d y d 11 10 d on/off control 12 analog outputs/inputs analog inputs/outputs = x a , x b , x c , x d pin 14 = v cc pin 7 = gnd mc54/74hc4066 function table pin assignment 11 12 13 14 8 9 10 5 4 3 2 1 7 6 y d x d d on/off control a on/off control v cc x c y c x b y b y a x a gnd c on/off control b on/off control on/off control state of input analog switch loff hon d suffix soic package case 751a03 n suffix plastic package case 64606 ordering information mc54hcxxxxj mc74hcxxxxn mc74hcxxxxd mc74hcxxxxdt ceramic plastic soic tssop 1 14 1 14 1 14 dt suffix tssop package case 948g01 j suffix ceramic package case 63208 1 14
mc54/74hc4066 ??????????????????????? ??????????????????????? maximum ratings* ??? ??? symbol ?????????????? ?????????????? parameter ?????? ?????? value ??? ??? unit ??? ??? v cc ?????????????? ?????????????? positive dc supply voltage (referenced to gnd) ?????? ?????? 0.5 to + 14.0 ??? ??? v ??? ??? v is ?????????????? ?????????????? analog input voltage (referenced to gnd) ?????? ?????? 0.5 to v cc + 0.5 ??? ??? v ??? ??? v in ?????????????? ?????????????? digital input voltage (referenced to gnd) ?????? ?????? 1.5 to v cc + 1.5 ??? ??? v ??? ??? i ?????????????? ?????????????? dc current into or out of any pin ?????? ?????? 25 ??? ??? ma ??? ? ? ? ??? p d ?????????????? ? ???????????? ? ?????????????? power dissipation in still air, plastic or ceramic dip2 soic package2 tssop package2 ?????? ? ???? ? ?????? 750 500 450 ??? ? ? ? ??? mw ??? ??? t stg ?????????????? ?????????????? storage temperature ?????? ?????? 65 to + 150 ??? ??? c ??? ? ? ? ? ? ? ??? t l ?????????????? ? ???????????? ? ? ???????????? ? ?????????????? lead temperature, 1 mm from case for 10 seconds (plastic dip, soic or tssop package) (ceramic dip) ?????? ? ???? ? ? ???? ? ?????? 260 300 ??? ? ? ? ? ? ? ??? c * maximum ratings are those values beyond which damage to the device may occur. functional operation should be restricted to the recommended operating conditions. 2derating e plastic dip: 10 mw/ c from 65 to 125 c ceramic dip: 10 mw/ c from 100 to 125 c soic package: 7 mw/ c from 65 to 125 c tssop package: 6.1 mw/ c from 65 to 125 c recommended operating conditions ???? ? ?? ? symbol ?????????????? ? ???????????? ? parameter ??? ? ? ? min ??? ? ? ? max ??? ? ? ? unit ???? ? ?? ? v cc ?????????????? ? ???????????? ? positive dc supply voltage (referenced to gnd) ??? ? ? ? 2.0 ??? ? ? ? 12.0 ??? ? ? ? v ???? ???? v is ?????????????? ?????????????? analog input voltage (referenced to gnd) ??? ??? gnd ??? ??? v cc ??? ??? v ???? ???? v in ?????????????? ?????????????? digital input voltage (referenced to gnd) ??? ??? gnd ??? ??? v cc ??? ??? v ???? ???? v io * ?????????????? ?????????????? static or dynamic voltage across switch ??? ??? e ??? ??? 1.2 ??? ??? v ???? ???? t a ?????????????? ?????????????? operating temperature, all package types ??? ??? 55 ??? ??? + 125 ??? ??? c ???? ? ?? ? ? ?? ? ? ?? ? ???? t r , t f ?????????????? ? ???????????? ? ? ???????????? ? ? ???????????? ? ?????????????? input rise and fall time, on/off control inputs (figure 10) v cc = 2.0 v v cc = 4.5 v v cc = 9.0 v v cc = 12.0 v ??? ? ? ? ? ? ? ? ? ? ??? 0 0 0 0 ??? ? ? ? ? ? ? ? ? ? ??? 1000 500 400 250 ??? ? ? ? ? ? ? ? ? ? ??? ns * for voltage drops across the switch greater than 1.2 v (switch on), excessive v cc current may be drawn; i.e., the current out of the switch may contain both v cc and switch input components. the reliability of the device will be unaffected unless the maximum ratings are exceeded. dc electrical characteristic digital section (voltages referenced to gnd) ???? ???? ????????? ????????? ????????? ????????? ???? ???? ????????? ????????? guaranteed limit ??? ??? ???? ? ?? ? ???? symbol ????????? ? ??????? ? ????????? parameter ????????? ? ??????? ? ????????? test conditions ???? ? ?? ? ???? v cc v ??? ? ? ? ??? 55 to 25 c ???? ? ?? ? ???? 85 c ???? ? ?? ? ???? 125 c ??? ? ? ? ??? unit ???? ? ?? ? ???? v ih ????????? ? ??????? ? ????????? minimum highlevel voltage on/off control inputs ????????? ? ??????? ? ????????? r on = per spec ???? ? ?? ? ???? 2.0 4.5 9.0 12.0 ??? ? ? ? ??? 1.5 3.15 6.3 8.4 ???? ? ?? ? ???? 1.5 3.15 6.3 8.4 ???? ? ?? ? ???? 1.5 3.15 6.3 8.4 ??? ? ? ? ??? v ???? ? ?? ? ? ?? ? ???? v il ????????? ? ??????? ? ? ??????? ? ????????? maximum lowlevel voltage on/off control inputs ????????? ? ??????? ? ? ??????? ? ????????? r on = per spec ???? ? ?? ? ? ?? ? ???? 2.0 4.5 9.0 12.0 ??? ? ? ? ? ? ? ??? 0.3 0.9 1.8 2.4 ???? ? ?? ? ? ?? ? ???? 0.3 0.9 1.8 2.4 ???? ? ?? ? ? ?? ? ???? 0.3 0.9 1.8 2.4 ??? ? ? ? ? ? ? ??? v ???? ? ?? ? ???? i in ????????? ? ??????? ? ????????? maximum input leakage current on/off control inputs ????????? ? ??????? ? ????????? v in = v cc or gnd ???? ? ?? ? ???? 12.0 ??? ? ? ? ??? 0.1 ???? ? ?? ? ???? 1.0 ???? ? ?? ? ???? 1.0 ??? ? ? ? ??? m a ???? ? ?? ? ???? i cc ????????? ? ??????? ? ????????? maximum quiescent supply current (per package) ????????? ? ??????? ? ????????? v in = v cc or gnd v io = 0 v ???? ? ?? ? ???? 6.0 12.0 ??? ? ? ? ??? 2 8 ???? ? ?? ? ???? 20 80 ???? ? ?? ? ???? 40 160 ??? ? ? ? ??? m a this device contains protection circuitry to guard against damage due to high static voltages or electric fields. however, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this highimpedance cir- cuit. for proper operation, v in and v out should be constrained to the range gnd (v in or v out ) v cc . unused inputs must always be tied to an appropriate logic voltage level (e.g., either gnd or v cc ). unused outputs must be left open. i/o pins must be connected to a properly terminated line or bus.
mc54/74hc4066 dc electrical characteristics analog section (voltages referenced to gnd) ???? ???? ????????? ????????? ????????? ????????? ???? ???? ????????? ????????? guaranteed limit ??? ??? ???? ? ?? ? ???? symbol ????????? ? ??????? ? ????????? parameter ????????? ? ??????? ? ????????? test conditions ???? ? ?? ? ???? v cc v ??? ? ? ? ??? 55 to 25 c ???? ? ?? ? ???? 85 c ???? ? ?? ? ???? 125 c ??? ? ? ? ??? unit ???? ? ?? ? ? ?? ? ???? r on ????????? ? ??????? ? ? ??????? ? ????????? maximum aono resistance ????????? ? ??????? ? ? ??????? ? ????????? v in = v ih v is = v cc to gnd i s 2.0 ma (figures 1, 2) ???? ? ?? ? ? ?? ? ???? 2.02 4.5 9.0 12.0 ??? ? ? ? ? ? ? ??? e 170 85 85 ???? ? ?? ? ? ?? ? ???? e 215 106 106 ???? ? ?? ? ? ?? ? ???? e 255 130 130 ??? ? ? ? ? ? ? ??? w ???? ? ?? ? ? ?? ? ???? ????????? ? ??????? ? ? ??????? ? ????????? ????????? ? ??????? ? ? ??????? ? ????????? v in = v ih v is = v cc or gnd (endpoints) i s 2.0 ma (figures 1, 2) ???? ? ?? ? ? ?? ? ???? 2.0 4.5 9.0 12.0 ??? ? ? ? ? ? ? ??? e 85 63 63 ???? ? ?? ? ? ?? ? ???? e 106 78 78 ???? ? ?? ? ? ?? ? ???? e 130 95 95 ??? ? ? ? ? ? ? ??? ???? ? ?? ? ? ?? ? ???? d r on ????????? ? ??????? ? ? ??????? ? ????????? maximum difference in aono resistance between any two channels in the same package ????????? ? ??????? ? ? ??????? ? ????????? v in = v ih v is = 1/2 (v cc gnd) i s 2.0 ma ???? ? ?? ? ? ?? ? ???? 2.0 4.5 9.0 12.0 ??? ? ? ? ? ? ? ??? e 30 20 20 ???? ? ?? ? ? ?? ? ???? e 35 25 25 ???? ? ?? ? ? ?? ? ???? e 40 30 30 ??? ? ? ? ? ? ? ??? w ???? ? ?? ? ???? i off ????????? ? ??????? ? ????????? maximum offchannel leakage current, any one channel ????????? ? ??????? ? ????????? v in = v il v io = v cc or gnd switch off (figure 3) ???? ? ?? ? ???? 12.0 ??? ? ? ? ??? 0.1 ???? ? ?? ? ???? 0.5 ???? ? ?? ? ???? 1.0 ??? ? ? ? ??? m a ???? ? ?? ? ???? i on ????????? ? ??????? ? ????????? maximum onchannel leakage current, any one channel ????????? ? ??????? ? ????????? v in = v ih v is = v cc or gnd (figure 4) ???? ? ?? ? ???? 12.0 ??? ? ? ? ??? 0.1 ???? ? ?? ? ???? 0.5 ???? ? ?? ? ???? 1.0 ??? ? ? ? ??? m a 2at supply voltage (v cc gnd) approaching 2 v the analog switchon resistance becomes extremely nonlinear. therefore, for lowvoltage operation, it is recommended that these devices only be used to control digital signals. ac electrical characteristics (c l = 50 pf, on/off control inputs: t r = t f = 6 ns) ???? ???? ????????????????? ????????????????? ???? ???? ????????? ????????? guaranteed limit ??? ??? ???? ? ?? ? ???? symbol ????????????????? ? ??????????????? ? ????????????????? parameter ???? ? ?? ? ???? v cc v ??? ? ? ? ??? 55 to 25 c ???? ? ?? ? ???? 85 c ???? ? ?? ? ???? 125 c ??? ? ? ? ??? unit ???? ? ?? ? ? ?? ? ???? t plh , t phl ????????????????? ? ??????????????? ? ? ??????????????? ? ????????????????? maximum propagation delay, analog input to analog output (figures 8 and 9) ???? ? ?? ? ? ?? ? ???? 2.0 4.5 9.0 12.0 ??? ? ? ? ? ? ? ??? 50 10 10 10 ???? ? ?? ? ? ?? ? ???? 65 13 13 13 ???? ? ?? ? ? ?? ? ???? 75 15 15 15 ??? ? ? ? ? ? ? ??? ns ???? ? ?? ? ? ?? ? ???? t plz , t phz ????????????????? ? ??????????????? ? ? ??????????????? ? ????????????????? maximum propagation delay, on/off control to analog output (figures 10 and 11) ???? ? ?? ? ? ?? ? ???? 2.0 4.5 9.0 12.0 ??? ? ? ? ? ? ? ??? 150 30 30 30 ???? ? ?? ? ? ?? ? ???? 190 38 30 30 ???? ? ?? ? ? ?? ? ???? 225 45 30 30 ??? ? ? ? ? ? ? ??? ns ???? ? ?? ? ? ?? ? ???? t pzl , t pzh ????????????????? ? ??????????????? ? ? ??????????????? ? ????????????????? maximum propagation delay, on/off control to analog output (figures 10 and 1 1) ???? ? ?? ? ? ?? ? ???? 2.0 4.5 9.0 12.0 ??? ? ? ? ? ? ? ??? 125 25 25 25 ???? ? ?? ? ? ?? ? ???? 160 32 32 32 ???? ? ?? ? ? ?? ? ???? 185 37 37 37 ??? ? ? ? ? ? ? ??? ns ???? ???? c ????????????????? ????????????????? maximum capacitance on/off control input ???? ???? e ??? ??? 10 ???? ???? 10 ???? ???? 10 ??? ??? pf ???? ? ?? ? ???? ????????????????? ? ??????????????? ? ????????????????? control input = gnd analog i/o feedthrough ???? ? ?? ? ???? e e ??? ? ? ? ??? 35 1.0 ???? ? ?? ? ???? 35 1.0 ???? ? ?? ? ???? 35 1.0 ??? ? ? ? ??? typical @ 25 c, v cc = 5.0 v c pd power dissipation capacitance (per switch) (figure 13)* 15 pf
mc54/74hc4066 additional application characteristics (voltages referenced to gnd unless noted) ???? ? ?? ? ? ?? ? symbol ?????????? ? ???????? ? ? ???????? ? parameter ?????????????? ? ???????????? ? ? ???????????? ? test conditions ??? ? ? ? ? ? ? v cc v ???? ? ?? ? ? ?? ? limit* 25 c 54/74hc ??? ? ? ? ? ? ? unit ???? ? ?? ? ? ?? ? ???? bw ?????????? ? ???????? ? ? ???????? ? ?????????? maximum onchannel bandwidth or minimum frequency response (figure 5) ?????????????? ? ???????????? ? ? ???????????? ? ?????????????? f in = 1 mhz sine wave adjust f in voltage to obtain 0 dbm at v os increase f in frequency until db meter reads 3 db r l = 50 w , c l = 10 pf ??? ? ? ? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ???? 150 160 160 ??? ? ? ? ? ? ? ??? mhz ???? ? ?? ? ? ?? ? ???? e ?????????? ? ???????? ? ? ???????? ? ?????????? offchannel feedthrough isolation (figure 6) ?????????????? ? ???????????? ? ? ???????????? ? ?????????????? f in sine wave adjust f in voltage to obtain 0 dbm at v is f in = 10 khz, r l = 600 w , c l = 50 pf ??? ? ? ? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ???? 50 50 50 ??? ? ? ? ? ? ? ??? db ???? ? ?? ? ???? ?????????? ? ???????? ? ?????????? ?????????????? ? ???????????? ? ?????????????? f in = 1.0 mhz, r l = 50 w , c l = 10 pf ??? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ???? 40 40 40 ??? ? ? ? ??? ???? ? ?? ? ???? e ?????????? ? ???????? ? ?????????? feedthrough noise, control to switch (figure 7) ?????????????? ? ???????????? ? ?????????????? v in 1 mhz square wave (t r = t f = 6 ns) adjust r l at setup so that i s = 0 a r l = 600 w , c l = 50 pf ??? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ???? 60 130 200 ??? ? ? ? ??? mv pp ???? ? ?? ? ? ?? ? ???? ?????????? ? ???????? ? ? ???????? ? ?????????? ?????????????? ? ???????????? ? ? ???????????? ? ?????????????? r l = 10 k w , c l = 10 pf ??? ? ? ? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ???? 30 65 100 ??? ? ? ? ? ? ? ??? ???? ? ?? ? ???? e ?????????? ? ???????? ? ?????????? crosstalk between any two switches (figure 12) ?????????????? ? ???????????? ? ?????????????? f in sine wave adjust f in voltage to obtain 0 dbm at v is f in = 10 khz, r l = 600 w , c l = 50 pf ??? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ???? 70 70 70 ??? ? ? ? ??? db ???? ? ?? ? ???? ?????????? ? ???????? ? ?????????? ?????????????? ? ???????????? ? ?????????????? f in = 1.0 mhz, r l = 50 w , c l = 10 pf ??? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ???? 80 80 80 ??? ? ? ? ??? ???? ? ?? ? ? ?? ? ? ?? ? ???? thd ?????????? ? ???????? ? ? ???????? ? ? ???????? ? ?????????? total harmonic distortion (figure 14) ?????????????? ? ???????????? ? ? ???????????? ? ? ???????????? ? ?????????????? f in = 1 khz, r l = 10 k w , c l = 50 pf thd = thd measured thd source v is = 4.0 v pp sine wave v is = 8.0 v pp sine wave v is = 11.0 v pp sine wave ??? ? ? ? ? ? ? ? ? ? ??? 4.5 9.0 12.0 ???? ? ?? ? ? ?? ? ? ?? ? ???? 0.10 0.06 0.04 ??? ? ? ? ? ? ? ? ? ? ??? % * guaranteed limits not tested. determined by design and verified by qualification.
mc54/74hc4066 figure 1a. typical on resistance, v cc = 2.0 v figure 1b. typical on resistance, v cc = 4.5 v 600 500 400 300 200 100 0 2.00 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0 v in , input voltage (volts), referenced to gnd -55 c 25 c 125 c r on , o n re s i s tan c e (o hm s) 120 100 80 60 40 20 0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 v in , input voltage (volts), referenced to gnd r on , on resistance (ohms) 125 c 25 c -55 c 80 70 60 50 40 30 20 10 0 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 figure 1c. typical on resistance, v cc = 6.0 v v in , input voltage (volts), referenced to gnd r on , o n re s i s tan c e (o hm s) 125 c 25 c -55 c 120 100 80 60 40 20 0 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 figure 1d. typical on resistance, v cc = 9.0 v v in , input voltage (volts), referenced to gnd r on , on resistance (ohms) 125 c 25 c -55 c 80 70 60 50 40 30 20 10 0 12 11 10 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 r on , on resistance (ohms) figure 1e. typical on resistance, v cc = 12 v v in , input voltage (volts), referenced to gnd figure 2. on resistance test setup plotter mini computer programmable power supply dc analyzer v cc + - analog in common out gnd device under test 125 c 25 c -55 c
mc54/74hc4066 figure 3. maximum off channel leakage current, any one channel, test setup off 7 14 v cc a v cc gnd v cc selected control input v il figure 4. maximum on channel leakage current, test setup on 14 v cc n/c a gnd v cc 7 selected control input v ih figure 5. maximum onchannel bandwidth test setup on 14 v cc 0.1 m f c l * f in db meter *includes all probe and jig capacitance. v os 7 selected control input v cc figure 6. offchannel feedthrough isolation, test setup off 7 14 v cc 0.1 m f c l * f in db meter *includes all probe and jig capacitance. v os r l v is selected control input figure 7. feedthrough noise, on/off control to analog out, test setup 14 v cc c l * *includes all probe and jig capacitance. off/on v cc gnd v in 1 mhz t r = t f = 6 ns control v cc/2 r l i s r l v os 7 selected control input v cc/2 v cc gnd analog in analog out 50% t plh t phl 50% figure 8. propagation delays, analog in to analog out
mc54/74hc4066 positionwhen testing t plz and t pzl figure 9. propagation delay test setup on 14 v cc *includes all probe and jig capacitance. test point analog out analog in c l * 7 selected control input v cc t r t f v cc gnd high impedance v ol v oh high impedance control analog out 90% 50% 10% 50% 50% 10% 90% t pzh t phz t pzl t plz figure 10. propagation delay, on/off control to analog out on/off v cc test point 14 v cc 1 k w positionwhen testing t phz and t pzh c l * 1 2 1 2 figure 11. propagation delay test setup 1 2 7 selected control input figure 12. crosstalk between any two switches, test setup r l on 14 v cc or gnd c l * *includes all probe and jig capacitance. off r l r l v is r l c l * v os f in 0.1 m f v cc/2 v cc/2 7 selected control input v cc/2 figure 13. power dissipation capacitance test setup 14 v cc n/c off/on a n/c 7 selected control input on/off control on v cc 0.1 m f c l * f in r l to distortion meter *includes all probe and jig capacitance. v os v is 7 selected control input v cc figure 14. total harmonic distortion, test setup *includes all probe and jig capacitance. v cc v cc/2
mc54/74hc4066 0 -10 -20 -30 -40 -50 1.0 2.0 frequency (khz) dbm -60 -70 -80 -90 fundamental frequency device source figure 15. plot, harmonic distortion 3.0 application information the on/off control pins should be at v cc or gnd logic levels, v cc being recognized as logic high and gnd being recognized as a logic low. unused analog inputs/outputs may be left floating (not connected). however, it is advisable to tie unused analog inputs and outputs to v cc or gnd through a low value resistor. this minimizes crosstalk and feedthrough noise that may be pickedup by the unused i/o pins. the maximum analog voltage swings are determined by the supply voltages v cc and gnd. the positive peak analog voltage should not exceed v cc . similarly, the negative peak analog voltage should not go below gnd. in the example below, the difference between v cc and gnd is twelve volts. therefore, using the configuration in figure 16, a maximum analog signal of twelve volts peaktopeak can be con- trolled. when voltage transients above v cc and/or below gnd are anticipated on the analog channels, external diodes (dx) are recommended as shown in figure 17. these diodes should be small signal, fast turnon types able to absorb the maximum anticipated current surges during clipping. an alternate method would be to replace the dx diodes with mo sorbs (high current surge protectors). mo sorbs are fast turnon devices ideally suited for precise dc protection with no inherent wear out mechanism. analog o/i on 14 v cc = 12 v analog i/o + 12 v 0 v + 12 v 0 v other control inputs (v cc or gnd) on 16 v cc d x d x v cc d x figure 16. 12 v application figure 17. transient suppressor application 7 selected control input d x other control inputs (v cc or gnd) 7 selected control input v cc
mc54/74hc4066 +5 v 14 hc4016 control inputs 7 5 6 14 15 lsttl/ nmos analog signals r* r* r* r* analog signals hct buffer r* = 2 to 10 k w v dd = 5 v v cc = 5 to 12 v analog signals analog signals 116 14 hc4016 control inputs 7 8 mc14504 13 3 5 7 9 11 14 2 4 6 10 5 6 14 15 channel 4 channel 3 channel 2 channel 1 1 of 4 switches common i/o 1234 control inputs input output 0.01 m f lf356 or equivalent a. using pull-up resistors b. using hct buffer figure 18. lsttl/nmos to hcmos interface figure 19. ttl/nmostocmos level converter analog signal peaktopeak greater than 5 v (also see hc4316) figure 20. 4input multiplexer figure 21. sample/hold amplifier + - 1 of 4 switches +5 v 14 hc4016 control inputs 7 5 6 14 15 lsttl/ nmos analog signals analog signals 1 of 4 switches 1 of 4 switches 1 of 4 switches
mc54/74hc4066 outline dimensions j suffix ceramic dip package case 63208 issue y min min max max inches millimeters dim a b c d f g j k l m n 0.785 0.280 0.200 0.020 0.065 0.015 0.170 15 0.040 0.750 0.245 0.155 0.015 0.055 0.008 0.125 0 0.020 19.94 7.11 5.08 0.50 1.65 0.38 4.31 15 1.01 19.05 6.23 3.94 0.39 1.40 0.21 3.18 0 0.51 0.100 bsc 0.300 bsc 2.54 bsc 7.62 bsc notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. dimension l to center of lead when formed parallel. 4. dimesnion f may narrow to 0.76 (0.030) where the lead enters the ceramic body. 14 8 17 -a- -b- -t- seating plane fg n k c l m 0.25 (0.010) t a m s 0.25 (0.010) t b m s j 14 pl d 14 pl n suffix plastic dip package case 64606 issue l notes: 1. leads within 0.13 (0.005) radius of true position at seating plane at maximum material condition. 2. dimension l to center of leads when formed parallel. 3. dimension b does not include mold flash. 4. rounded corners optional. 17 14 8 b a f hg d k c n l j m seating plane dim min max min max millimeters inches a 0.715 0.770 18.16 19.56 b 0.240 0.260 6.10 6.60 c 0.145 0.185 3.69 4.69 d 0.015 0.021 0.38 0.53 f 0.040 0.070 1.02 1.78 g 0.100 bsc 2.54 bsc h 0.052 0.095 1.32 2.41 j 0.008 0.015 0.20 0.38 k 0.115 0.135 2.92 3.43 l 0.300 bsc 7.62 bsc m 0 10 0 10 n 0.015 0.039 0.39 1.01
mc54/74hc4066 outline dimensions d suffix plastic soic package case 751a03 issue f min min max max millimeters inches dim a b c d f g j k m p r 8.55 3.80 1.35 0.35 0.40 0.19 0.10 0 5.80 0.25 8.75 4.00 1.75 0.49 1.25 0.25 0.25 7 6.20 0.50 0.337 0.150 0.054 0.014 0.016 0.008 0.004 0 0.228 0.010 0.344 0.157 0.068 0.019 0.049 0.009 0.009 7 0.244 0.019 1.27 bsc 0.050 bsc notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. a b p 7 pl g c k seating plane d 14 pl m j r x 45 1 7 8 14 0.25 (0.010) t b a m s s b 0.25 (0.010) m m f dt suffix plastic tssop package case 948g01 issue o dim min max min max inches millimeters a 4.90 5.10 0.193 0.200 b 4.30 4.50 0.169 0.177 c --- 1.20 --- 0.047 d 0.05 0.15 0.002 0.006 f 0.50 0.75 0.020 0.030 g 0.65 bsc 0.026 bsc h 0.50 0.60 0.020 0.024 j 0.09 0.20 0.004 0.008 j1 0.09 0.16 0.004 0.006 k 0.19 0.30 0.007 0.012 k1 0.19 0.25 0.007 0.010 l 6.40 bsc 0.252 bsc m 0 8 0 8 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a does not include mold flash, protrusions or gate burrs. mold flash or gate burrs shall not exceed 0.15 (0.006) per side. 4. dimension b does not include interlead flash or protrusion. interlead flash or protrusion shall not exceed 0.25 (0.010) per side. 5. dimension k does not include dambar protrusion. allowable dambar protrusion shall be 0.08 (0.003) total in excess of the k dimension at maximum material condition. 6. terminal numbers are shown for reference only. 7. dimension a and b are to be determined at datum plane -w-. s u 0.15 (0.006) t 2x l/2 s u m 0.10 (0.004) v s t l u seating plane 0.10 (0.004) t ??? ??? section nn detail e j j1 k k1 detail e f m w 0.25 (0.010) 8 14 7 1 pin 1 ident. h g a d c b s u 0.15 (0.006) t v 14x ref k n n
mc54/74hc4066 on semiconductor and are trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. atypicalo parameters which may be provided in scill c data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthori zed use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. publication ordering information japan : on semiconductor, japan customer focus center 4321 nishigotanda, shinagawaku, tokyo, japan 1410031 phone : 81357402700 email : r14525@onsemi.com on semiconductor website : http://onsemi.com for additional information, please contact your local sales representative. mc74hc4066/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 3036752175 or 8003443860 toll free usa/canada fax : 3036752176 or 8003443867 toll free usa/canada email : onlit@hibbertco.com n. american technical support : 8002829855 toll free usa/canada

▲Up To Search▲

Price & Availability of MC74HC4066-D

	To Download MC74HC4066-D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .